inet 10.64.1.187 netmask ffffff00 broadcast 10.64.1.255 groupname ipmp0 ether 0:21:28:49:a7:2e *# ldm ls-services primary *VCC NAME LDOM PORT-RANGE

Its been a while since i got stuck up with similar issue. I want to automate setting non-global zonal interface MTU=1496. I have configured zones on my Solaris System. # ifconfig -a lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 lo0:1: flags=2001000849 mtu 8232 index 1 zone db inet One of the common mistakes done while configuring the guest LDOMs for the first time is - to not configure control domain for inter domain communications. In this case the control domain and guest ldoms can talk to everyone on the network but not to each other. Hi, I am not able to change my netmask for bge0 NIC. I've just run Oracle CRS installer and it changed my netmask. I didn't install CRS. bash-3.00# ifconfig -a lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843 mtu 1500 index 2 inet 10.160.19.49 netmask ff000000 broadcast 10 ifconfig vmxnet3s1:1 10.20.20.20 netmask 255.255.255.255 Then I added this IP address to the /etc/hosts file and restarted the network by executing: svcadm restart network/physical But when I try to ping this new IP address from another server, it reports "no answer from 10.20.20.20". Feb 28, 2017 · The reality is that netmask are bits, AIX does it differently than others on the ifconfig, but it is naive to think the netmask can only be presented in 4 octects. There is a common notation that uses the sum of the enabled bits on the netmask, thus 255.255.255 or ffffff00 is actually /24

# ifconfig net0 net0: flags=1000843 mtu 1500 index 2 inet 10.53.77.154 netmask ffffff00 broadcast 10.53.77.255 ether 0:10:e0:3a:c4:d8 Its netmask should be fffffc00, but whenever I am rebooting this server, it takes ffffff00.

Jun 03, 2020 · inet 192.168.0.100 netmask ffffff00 broadcast 192.168.0.255 ether 0:c:29:70:da:5b To check the default route or gateway # netstat -rn Routing Table: IPv4 Destination Jun 26, 2013 · Arena-Node1#ifconfig -a lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g0: flags=1000843 mtu 1500 index 2 inet 192.168.2.5 netmask ffffff00 broadcast 192.168.2.255 ether 0:c:29:ec:b3:af e1000g1: flags=19000802 mtu 0 index 3 inet 0.0.0.0 netmask 0 groupname arenagroup-1 ether 0:c:29:ec:b3:b9 e1000g2: flags=1000842 inet 192.52.32.15 netmask ffffff00 broadcast 192.52.32.255 As I said ifconfig command shows a lot of details but I have only included relevant inet one if you have more than one network card attached to that host, you may see more than one inet address corresponding to each of them.

inet 10.64.1.187 netmask ffffff00 broadcast 10.64.1.255 groupname ipmp0 ether 0:21:28:49:a7:2e *# ldm ls-services primary *VCC NAME LDOM PORT-RANGE

Connect your computer to the routers WAN port with an ethernet cable and configure the IP address to 192.168.1.2 with netmask 255.255.255.0 and start the TFTP server on your computer. Now you need to connect a RS232-to- TTL cable to the serial header (do not connect VCC) as shown in the table below. Mar 03, 2010 · lo0:1: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:1: flags=1000843 mtu 1500 index 2 inet XXX.XXX.XX.XXX netmask ffffff00 broadcast XXX.XXX.XX.XXX bge0:3: flags=1000843 mtu 1500 index 2 inet XXX.XXX.XX.XXX netmask ffffff00 broadcast XXX.XXX.XX.XXX That's it! you're done. In case you want to remove the interface - Mar 12, 2019 · The hme0:1 interface is now configured, it has a default netmask of ffffff00 (255.255.255.0), and it has a broadcast address of 192.169.1.255. You could have assigned different values if you wanted to. May 05, 2014 · inet 10.158.169.10 netmask ffffff00 3. Verify the the name service is properly defined in the name service switch file (nsswitch.conf(4)) and the hostname is defined in the hosts database, e.g. hosts(4) file. iperfserv% dladm show-phys net0 LINK MEDIA STATE SPEED DUPLEX DEVICE net0 Ethernet up 1000 full igb0 iperfserv% ifconfig net0 | grep inet inet 10.129.193.63 netmask ffffff00 broadcast 10.129.193.255 iperfserv% ./iperf -v iperf version 3.0-BETA5 (28 March 2013)SunOS iperfserv 5.11 11.1 sun4v sparc sun4v iperfserv% ./iperf -s -i 1-----Server listening on 5201----- inet 129.147.11.59 netmask ffffff00 broadcast 129.147.11.255 hme0: flags=863 mtu 1500 inet 172.20.4.110 netmask ffffff00 broadcast 172.20.4.255 # The verbose mode switch, -v displays additional information, including the MTU size configured for the interface: